Bunny_Operator

27/05/2026

The ARIC and RAP experiment continues.

I was unable to get my 13.9 Mid to function 100% with either the C or C- variant. has the C variant that functioned 100% with 12.5 Car, so I opined that Carbine gas might be the way to go.

The result was a spare parts bin upper build using a Centurion Arms 12.5 Car barrel w/ FSB. I opted to use their legacy CMR cutout handguard and RRA riser for a unique "vibe" and I think it turned out eye-pleasing with the EXPS3-1. The dot only config is growing on me.

The optic centerline is at 3.25" and close to a 1.7" riser config. I cannot use the irons without removing the optic, so I might swap to the XPS variant or a different optic setup later if I care enough.

Also, shout out to and for the superb 3P15 Plan B muzzle device. It's one of my favorites.

Check out RD's https://silencerresource.com/ for solid MD/Suppressor data.

Range Report:
Carbine gas did the job and the C- variant was functioning unsuppressed. I did try a few rounds suppressed (standard pressure) but it was definitely gassy and punchy as expected. I have the C variant in currently and will field that next time out to confirm function.

Note that the C and C- variants are not intended to be used suppressed, so I've also reached out to the ARIC engineer to request the M variant as it has additional vents to counter the increased gas.

I'm glad that I got this working and can move on to further experimentation like maybe 300 BO and low pressure cans.

I want this to be successful because this setup is such a vibe paired with the AX556/ADAC lower.

That is all for now. Deuces.

See my profile for additional codes and resources. Help support the good folks who support us.
2A Resources

Vibes

Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales.

17/05/2026

M1X completed
(26X, Baby Roland Special)

The M1X frame is pre-installed with the Gen 4/5 mag release and slide lock lever. It is Gen 3-5 parts compatible and up to the end user to complete the rest. Note that if you're opting for Gen 5, ensure that your slide is cut for the ambi slide stop.

I opted to use Gen 3 slide, internals, and a few upgrades:
- Timney Enhanced Feel Shoe
- KKM barrel and comp
- Vickers/TangoDown Gen 4/5 extended mag release
- Trijicon SRO
- ISMI RSA w/ 17 # spring

The frame is utilizes the same dustcover rail as the slim line series (43X/48), so I applied the Streamlight TLR7-Sub. Holsters are available at on the G***kStore site.

Additional frame colors have been released since mine was acquired (1st run version), so options for everyone.

I haven't decided if I'll opt for a magwell (Gen 5 compatible) or use the GS brass plug. I might use the Booth Grip Anchor like on my 19 and 48 for ergos. Might also swap to the PMM micro comp to reduce footprint further and leave this upper combo on the 26XX project.

Anyways, LMK if you have questions. Deuces.

See my profile for additional codes and resources. Help support the good folks who support us.
2A Resources

Vibes

Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales.

13/05/2026

Don't bridge your optics across your upper and handguard.

Topic came up and I realized that many don't understand the why, so here we are.

It is incredibly difficult to control how components will mate after install even if they're from the same OEM. Every part has acceptable tolerance variances and it is more work than necessary to ensure that the components are on the same plane. Tolerance stacking can also happen. Nevermind that if your handguard gets loose or impacted.

It is best to use a one-piece extended rail type accessory or a monolithic type receiver if you need the space.

If you have questions or wish to share your experiences, comment away.

See my profile for additional codes and resources. Help support the good folks who support us.
2A Resources

Vibes

Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales.

09/05/2026

The Venom Enclosed is a solid, affordable option for anyone that wants a "no frills" enclosed RDS but it has a taller deck height than its Defender cousin, so I questioned if it would affect the use of aftermarket plates. The Defender comes with an MOS specific plate (IMO is very good as is and an upgrade isn't necessary) but the Venom Enclosed does not.

The DPP/EFLX MOS plate was used as the sample. I like FCD because I know they use drawings from the OEMs vs reverse engineering, which gives me confidence that it very likely isn't the plate if something goes wrong. Also, I've known and worked with Roger for years and understand how he thinks. Thank you for this demo unit, Roger.

FCD had already addressed the Defender and XL series in their product description and I've confirmed that the instructions carry over to the Venom Enclosed. Use the Vortex supplied M4x0.7 9.8mm screws and they will be recessed-flush to the plate (see photos 3 & 4). The 11mm screws are too long in this example and will protrude past the plate causing damage since the screws don't pass through into the slide. Adjust according to your specific platform.

The combo sits perfect on the RXM experiment. I didn't like how the OEM RXM slide felt, so I applied a G***k 17 Gen 3 slide using the adapter. Shout out to for the initial idea. It is basically a 17 Gen 6 "the long way" given the single spring 19 RSA.

Current impressions:
- I should've had front serrations applied when doing the MOS race cut but tape is fine for now.
- Would benefit from extended mag release and slide stop
- I want more grip weight

That is all. Thanks for reading. Deuces.

See my profile for additional codes and other resources. Help support the good folks who support us.
2A Resources

Vibes

Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"

23/04/2026

DSA Para FAL 18"
Yet another project to calm the tisms. 🤣

I have a 21" Imbel kit built on an older, forged DSA receiver (allegedly LMT produced) and opted to leave it in "classic" config, so I hunted down a Para to "modernize" to some degree.

This is a factory DSA with all USA parts. I can feel the build quality differences from the Imbel but beggars can't be choosers.

I've already stripped the top cover components just from tearing down the unit. They really should've used steel instead of aluminum hardware. The handguard is meh and will probably bend (I should find the VLTOR one). LOP between Para and classic are about the same.

I do appreciate the extended controls though, albeit the springs/detents feel a little light on the bolt release and safety.

I've upgraded to DSA's metric folding charging handle (Photo 3) as the original k**b dug into my gut when slung.

I also tried the Belgian combo MD (similar to the one on the 21"), which mounts over the barrel and gives the illusion that the barrel is shorter but timing required machining the MD and I didn't want to deal with that, so I opted for the 9/16x24LH to 5/8x24RH adapter, which also mounts over the barrel. SF Warcomp was used as this caliber needs some form of compensation but does put the OAL closer to the 21".

No plans to can at this time but I do have the adjustable piston and can tune if I feel like it in the future. has examples of his suppressed, so check his page if you're interested.

This will evolve as I get annoyed by things during use. The Trijicon RX01 still sucks.

That is all. Deuces.

See my profile for additional codes and resources. Help support the good folks who support us.
2A Resources

Vibes

Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales.

07/04/2026

Resource highlight. Bookmark this.

was instrumental in assisting the homie at IG account recovery after Meta nuked it without warning. The process was painless and basically hands-off once the details were provided.

OSD is a grassroots 2A resource group started by folks with a wide range of experience from inside and outside the industry. I was quite impressed.

One of the founders is our high-vibes homie over at (my favorite shirt is the Kiki's Armed Delivery Service).

Check out their site for resources and the "about" page to learn more about the team. Sign up for the newsletter. If you need assistance reach out.

https://opensourcedefense.com/about

Thank you again for your help. You're a bunch of solid dudes.

See my profile for additional codes and resources. Help support the good folks who support us.
Affiliations

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales.

19/03/2026

Check out Revival Defense new Silencer Resource Center. It's a gold mine of information.

Free silencer compatibility database. Browse mounting systems, fitment data, adapter compatibility, and pin & weld configs from all major manufacturers.

18/03/2026

Victrix for the MP5 platform.

Shown here is an earlier prototype applied to an MKE AP5-P (MP5K clone). The Victrix is also rotary safety compatible and available for multiple MP5 patterns as shown through the Radiata profile and posts from other makers such as ****ms.

Contact one of Radiata's dealers if you are interested.

I've worked with Radiata for a long, long time and it has been a pleasure to be on the T&E team to ensure that the consumer receives the best products. It's been quite the journey and I am very proud to watch my buddy achieve his dreams.

Radiata also has the Fretensis (ban state version) for folks that need them. We're working on a few other products, so stay tuned.

Deuces

See my profile for links and other discount codes. Help support the good folks who support me.

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales. Content is for educational purposes only. All fi****ms are handled in a safe manner by professionals or with professional guidance.

27/02/2026

Widebody Grip Tape for Staccato 2011 HD series.

A few peers have experienced unintentional depression of the mag release when running the HD. We attributed this to the HD grip shape being different from the legacy Staccato 2011 variants.

I was browsing for solutions and came across this Kiral Defense's product, which replicates the legacy 2011 grip shape. The material/texture is silicon carbide and is a 2-piece system, so it provides increased traction with build-up at the grip.

We'll see if this solution helps to resolve the HD ergo issues for these fellas.

If you have experienced unintentional mag releases or have other ergonomic issues with the HD, let me know what they are and the solutions you've tried.

Deuces

See my profile for links and other discount codes. Help support the good folks who support me.

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales. Content is for educational purposes only. All fi****ms are handled in a safe manner by professionals or with professional guidance.

23/02/2026

One of my favorite setups running components from several of my favorite shops in the game.

The remain onboard and have provided on-the-fly usability.

I am very pleased with the mounts for this application's needs especially since I wanted to retain the use of the diopter sights (their first product!) while having the ability to run the magnifier.










I think a MAWL would work well here over a box design due to space limits but we'll see how the NV configuration turns out.

Deuces

See my profile for links and other discount codes. Help support the good folks who support me.

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales. Content is for educational purposes only. All fi****ms are handled in a safe manner by professionals or with professional guidance.

07/02/2026

Dad: Hold the damn flashlight properly, you sa-too-pit guy!

American Ranch 5.56 STANAG
Maxiumus-L in inconel, direct thread

Metal straight 20s hold a special place in my soul.

LPVOs are getting annoying to me.

ID the song.

Deuces.

See my profile for links and other discount codes. Help support the good folks who support me.

"bunny"
"bunny10"
"bunnyoperator"
"bunny15"
"bunny"
"bunny"and.atac "BUNNY13"
*Disclaimer: No fi****ms or ammunition sales. Content is for educational purposes only. All fi****ms are handled in a safe manner by professionals or with professional guidance.